There are several different styles of tub drain — two of the most common are threaded and drop-in drains. Threaded drains are usually found in older tubs, while the drop-in version is common in newer models. Determining whether you have one or the other involves a bit of inspection.
Do bathtub drains unscrew?
If your drain stopper has a set-screw, use a small screwdriver or a hex key to unscrew it.
Remove the Bathtub Drain Stopper
- Set the drain to its open position.
- Lift up on the drain stopper’s knob and turn it counterclockwise.
- After enough turns, the drain stopper should be unscrewed and come free from the drain opening.
Are all tub drains standard?
Thanks to the standardization, any bathtub drain can fit any standard bathtub between 14 and 26 inches in depth. The size of the drain is standardized because it needs to fit to the P-trap, which is the next component of the drain.
How do I know what type of tub drain I have?
What Kind of Tub Drain Do You Have?
- Toe Touch (Foot Actuated, Foot Lock or Toe Tap)
- Push-Pull or Lift and Turn.
- Pop-Up: Activated by Trip Lever, Cable, Turn Style, or other.
- Trip Lever or Turn Style (internal plunger/stopper)
Are all tub drains the same?
Not all bathtub assemblies and drain stoppers are the same. The right drain depends on the type of tub you have as well as other factors, including: The pipe assembly material.
How do you remove an old bathtub drain?
So you put that in there and there's different ways you can drive it you can use a you know socket wrench thing down here i usually just do it with a screwdriver going through the hole. There.
How do you remove a bathtub drain without the tool?
Quote from the video:
And some Tyler the locknut pliers stick the needle nose down in here. Use a little leverage. And the drain just spins right.
Are bathtub drains universal?
Bathtub drains are 1 1/2 inches wide and fit all standard bathtubs ranging from 14 to 26 inches deep. They are this size because they must fit the opening of the P-trap — also 1 1/2 inches wide — which is a special pipe that has a sharp bend in it.
Are tub drain locations standard?
The position of the tub drain will vary, depending on the size and design of the tub, and you’ll need to cut an access hole in the floor at the drain end of the tub to allow for positioning and installing the drain line. This hole should be 9 inches wide and extend at least 12 inches from the wall.
How do you measure a bathtub stopper?
Measure from the piping section where it branches out toward the drain over to the drain hole and write that horizontal distance measurement down. That will give you the length and width that is needed for your drain. Your local hardware or home improvement store should carry a bathtub drain that fits your needs.
Does a tub faucet have to be over the drain?
Having your faucet or showerhead and drain on opposite sides does not go against any building code regulations, and your tub will still drain perfectly fine.
Are all shower drains the same?
Keep in mind that shower drain assemblies are generally made to fit a 2-inch drainpipe, not the 1 1/2-inch pipe usually found on tubs. A 2-inch pipe is the recommended size because showers have a low threshold for flooding, and a 2-inch pipe helps the water drain faster than does a 1 1/2-inch pipe.
Why are tub and shower drains different sizes?
Pipe Connection Size Differences
Shower or tub drains have different drain connection sizes to accommodate the pipe sizes of your plumbing drain system. A shower tub drain has a 2” drain connection, while a tub drain often has a 1 ½” drain connection.
Can a tub and shower share the same drain?
Yes, they will both be using the same drain pipe at somepoint inside or outside of your house. But the the pipes must join well below the level of both items or the pipe must be large enough for the combined flow, otherwise when you put water down one of them, it will flow out of the other!
Does a shower trap have to be directly under the drain?
The maximum distance between the shower drain and the P-trap is 5 feet. However, the P-trap should be as close to the shower drain inlet as possible. You should even have the P-trap directly under the shower drain for the best results.
Can a sink and shower share the same drain?
Is It Possible to Have the Same Drain for the Shower and Sink? Yes, the drain for the shower and the sink can be the same. The shower and sink can use the same drain pipe if it is well below the sink and shower level.
Why does tub drain gurgle?
The main culprit that causes this gurgling noise is the clog that is forming inside your pipes. Air pockets can form and surround the clog. In turn, it causes the trapped air to exit up as the water flows down the drain.
Are toilet drains and sink drains connected?
Plumbing contractors can connect drain lines in the floor beneath the bathroom and install a vent that will allow water and waste to drain without forming an airlock. The sink drain will empty into the toilet drain line because the toilet has the largest drainpipe.
Why is water coming up my shower drain?
Your water may also be backing up into your tub drain if there’s a clog in the plumbing vent, which allows sewage air to escape out of your home through the roof. If leaves, pine needles, branches, or other debris on your roof block this vent, the sewage air, and water may come up through your drains.
Are all drains in a house connected?
Your sinks, toilets, showers, and washing machine each have their own branch line drains. These branch lines connect to your main house drain at some point. If your main house drain becomes clogged, all of the other drains in the house can back up.
What is the black stuff coming up from bathtub drain?
The “creepy black stuff” in your drain is made up of a combination of things, mostly decomposing hair, soap scum, toothpaste grit, shaving cream residue, skin cells, etc.