How do I fix my Bissell PowerForce Helix?

Why did my Bissell vacuum stop working?

The most common culprits behind Bissell vacuum cleaner charging and powering problems are unplugged power cords, faulty outlets, blown fuses, and faulty charging cables. In some cases, a Bissell vacuum cleaner might also fail to power down or turn on due to minute mechanical issues in the device handle.

Is there a reset button on a Bissell PowerForce Helix?

Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.

How do you take apart a Bissell PowerForce Helix?


Open the dirt container lid by lifting the release latch on the front remove the premotor filter. And pull the filter out to clean once it's clean and dry place it back in the dirt container lid.

Why is my Bissell PowerForce Helix vacuum brush not spinning?

Quote from the video:
The brushroll may have lodged debris or other entanglements keeping it from rotating to fix remove the brushroll and inspect it here's how to do it.

How do you fix a Bissell vacuum that won’t turn on?

Quote from the video:
Start by plugging in your vacuum to a grounded outlet to power on your vacuum step on the red power switch pedal on the back of the vacuum by the foot. If there's still no power unplug.

How do I fix my Bissell vacuum?

Quote from the video:
Cover grab both ends of the brush. And lift straight out of the vacuum while slipping the brush off the belt. Clear the brush roll of any hair and debris and inspect by placing it on its end and spin.

See also  How far apart should Shelves be in a linen closet?

Where is the Bissell CrossWave reset button?

The factory reset button on a Bissell CrossWave Max is located on the handle. It is the “Mode” button with the gear icon.

Why is my Bissell Pet Pro not turning on?

If the lights don’t turn on this means the machine has no power. Unplug the machine. Insert a screwdriver or similar object into the hole just below the top of the Quick Release Cord Wrap and remove the top of the handle. Reinsert the top of the handle so it clicks into place.

Where is the power button on the Bissell Cleanview?

Quote from the video:
Next push the red power switch on the pedal once to turn the unit on and again to turn the unit off to recline the unit press the recline pedal.

Why is my vacuum brush not spinning?

Vacuum Cleaner: Why doesn’t my vacuum cleaner’s brush roll spin? A broken drive belt, damaged brush roll, jammed brush roll bearings, tripped brush roll motor overload, failed brush roll motor or a wiring failure in the wand or nozzle can prevent the brush roll from spinning.

What do you do when your vacuum brush stops spinning?

Common solutions for: Vacuum cleaner brush not spinning



Inspect the belt to see if it is broken, stretched out, or out of place. If the cogged belt is broken or stretched out, replace it. Inspect the belt to see if it is broken, stretched out, or out of place. If the drive belt is broken or stretched out, replace it.

See also  Who are the Beales of GREY Gardens?

How do I know if my vacuum belt is broken?

Read on to find out.

  1. Your Vacuum Has Suddenly Gotten Extra Noisy. Let’s face it – no vacuum cleaner is exactly quiet, but when your faithful upright suddenly sounds like a jet engine, it could very well be your belt is about to break. …
  2. Your Suction Power has Slipped. …
  3. Your Vacuum Cleaner is Leaving a Trail. …
  4. Conclusion.


Can I use my vacuum without a belt?

Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won’t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.

Can you repair a vacuum belt?

Give vacuum performance a big boost with a new agitator belt



If it’s taking more work to vacuum your house, it’s probably time to replace the vacuum agitator belt. The good news is you can do it yourself in about fifteen minutes with two screwdrivers.