How do you put nails in a Porter Cable nail gun?

How do you load nails into a Porter Cable nail gun?

Quote from the video:
The magazine utilizes a two-step easy loading system load the nails into the rear of the magazine. Then slide the pusher back to engage the nails.

How do you load a porter cable staple gun?

Quote from the video:
As far as putting staples in it it's pretty straightforward. You have a release right here. And then your staples going right from the bottom. This is a smaller gauge staple by the way 22 gauge.

How do you load a 16 gauge Porter Cable nailer?

Quote from the video:
All you do is slide the nails into the bottom up to where the other nails are. And then push down the red button. Slide that back BAM it's loaded it's that simple.

How do you load a nail gun?

Quote from the video:
Just by simply dropping the nails into place and then just releasing the last mechanism that slides down and holds the nails in the rack.

How do you load a Porter Cable 18 gauge nail gun?

Quote from the video:
Making sure the tips are pointing to the front of the magazine. And the nails are under the nail guide in the channel. Next i'll push the magazine closed until it latches into place.

How do you get a jammed nail out of a Porter Cable nail gun?

Quote from the video:
Right in the center. Right before our front door is where these Brad nails will get jammed up you need to take a screwdriver and pry those out once the nails have been cleared.

How do you load a central pneumatic staple gun?

Quote from the video:
Then load the Brad nails from the side push them to the top then slide the magazine up until it clicks.

How do you put staples in a central pneumatic nail gun?

Quote from the video:
So take these staples out they just lift right off the top. So that just slips right over the top of that bar. The 18 gauge nails go in this tray just like they do on the other nailers.

See also  Can you put essential oils in a plastic bottle?

Can you use staples in a Porter Cable Brad Nailer?

With a 100 staple magazine capacity, this tool accepts 1/4 inch crown staples from 1/2 to 1-1/2 inches.

How do you install a pneumatic nail gun?

Quote from the video:
Just by simply dropping the nails into place. And then just releasing the latch mechanism that slides down and holds the nails in the rack.

How do you load a 2 inch brad nail?

Quote from the video:
You need to make sure that the nail head is sitting in those grooves it'll slide along in the groove. But it won't be able to jump outside of that groove.

Why does my nail gun not shoot nails?

Jams are the most common cause of a nailer not firing. Thankfully, they are often easy to clear. For safety, first disconnect the tool from the air supply, retract the feeder mechanism, and remove any excess fasteners from the magazine. From there, clearing the jam depends on what type of nailer you have.

Why is my nail gun blowing air out the back?

If you try to fire a pneumatic nail gun or stapler, but only hear air leaking when engaging the trigger, it’s likely that your tool’s “O-Ring” is not sealing properly. When the trigger is not depressed, you may not hear air leaking, as the valve is probably sealed.

Why is air coming out of the back of my nail gun?

Disassemble the nailer and inspect it parts for damage/wear, or take it to a shop. Air Leaks Out Back This is a good sign that seals need to be reseated with dry firing or bumping the gun, but it is also possible that air is leaking out the back of the tool because of a broken part.

See also  Are all shampoos biodegradable?

Why is my nail gun jamming?

What Caused the Jam: Lack of Adequate Oil: The air cylinder in the nose needs plenty of oil to function properly. Too little oil, and the nails will be slow to feed, causing a jam. Pro Tip: For coil nailers, use 10-15 drops of oil before nailing.

What happens if you don’t Oil your nail gun?

The O-rings in the tool will dry up, causing the tool to malfunction. It will also cause unnecessary wear on its components, and potentially cause corrosion.

How do you change the O ring on a nail gun?

Quote from the video:
If the bumper comes out of the gun you just place it right back inside with the driver unit removed. Now I can install the new o-ring I'll remove the old o-ring from the piston.

Will a nail gun fire without nails?

Nail compatibility



Insure that the nails are compatible with the gun. If they’re not, the gun may not fire, misfire, or self destruct. If it is making a “big” dent then it usually means that your nails are jammed.

How do you attach a hose to an air compressor nail gun?

Quote from the video:
Air compressor along with the rigid 15 gauge two and a half angled finish nailer turn on the compressor. And allow the. Pressure.

Does a nail gun shoot nails?

A full battery can discharge up to 400 nails, two to three nails per second. Cordless finish nail guns that are used for carpentry, woodwork, trim and molding can shoot out about 400 nails per hour. More expensive models can fire out up to five nails per second, in both hard and soft surfaces.

See also  What men wore in the sixties?

How do you lubricate a nail gun?

Quote from the video:
There would be winter gun oil and normal gun oil just different viscosities to allow the gun to work best at different temperatures.

Do you need to oil nail gun?

Traditional Oiled Nail Guns



Oiled nailers require regular lubrication to ensure they function properly. Adding a few drops of oil into the air inlet each time you use the tool reduces heat and friction and prevents valves, seals and O-rings from wearing out. During heavy use, you should oil the tool more frequently.

How often should you oil a nail gun?

Pneumatic Tools



To break down deposits and ensure smooth starts and stops, most pneumatic nailers and staplers require a total of 4-5 drops of pneumatic tool oil into the air fitting every day, adjusting for the amount of use.

Where do you put air tool oil?

Quote from the video:
Right into the air inlet. And if I press the trigger on the tool it lets the oil get right down inside on. The tool as well you will see it says oil daily as.

Can you put too much oil in an air tool?

However, filling your compressors oil sump to the top can cause significant internal damage to your unit. When excess amounts of oil become aerosolized by the compressor’s discharge, it can cause damages not only to your compressor, but to any pneumatic tools and accessories that are hooked up to your compressor.

Do you have to use air tool oil?

Air tool oil is a must for nearly every air tool. Use this page as a guide to keep your air tools running strong! Almost every air tool will need some type of lubrication. Some air tools may have a grease fitting, while others need daily lubrication.