How do you replace an automatic feed spool?

How do I fix the auto feed trimmer?

If the cap is damaged or worn it can malfunction causing wine not to advance to inspect the cap remove it and clean any debris. Replace. If necessary. Problem number three spools.

How do you replace a spool?

Quote from the video:
To remove the old spool press the tabs on the spool cover and pull the cover straight off next lift the spool out of the hub.

How does the Black & Decker Automatic Feed Spool work?

The Automatic Feed Spool (AFS) is the technologically advanced line feed system found on Black & Decker string trimmer products. Using centrifugal force, the system monitors the amount of line being used and feeds more line automatically as the cutting line shortens.

How does an automatic feed spool work?

Quote from the video:
After the trimmer reaches full speed release the trigger to advance the line 1/4 inch at a time repeat this step until you hear the line make contact with the line cutoff blade to prevent excess.

Why does my trimmer line not feed?

Quote from the video:
The trimmer line itself could be the wrong size for your trimmer or stuck in the trimmer. Head line that is too thick or too thin for the trimmer head won't feed properly.

Why does my strimmer line keep jamming?

The line of a Weed Eater trimmer head won’t advance if it is too short because not enough centrifugal force acts on it. That situation can happen if you don’t tap the head often enough or the line becomes sheared by a piece of wire or a root.

See also  How do you clean a non porcelain bathtub?

Why does my Ryobi trimmer not auto feed?

Many times the problem of string not feeding out is caused by badly wound string. The replacement string on the spool needs to be wound tightly and evenly. When the string overlaps or is loose on the spool, when the head starts spinning at full speed the string will get tangled and clogged inside the cutting head.

How do I turn off auto feeder?

Quote from the video:
Option. So to stop autofeed option all you need to do is you put your line through one of those grooves.

How do you replace the spool lever on a Black and Decker trimmer?

Quote from the video:
I simply line up the radius on the lever. With the same radius on the spool. And then press it into the hole on the top of the spool. Now reinstall the line spool. And the spool cap.

How do you replace a spool House?

Quote from the video:
And now I can install the new spool housing I'll line it with the bearing housing. And press it into place. And I'll reattach the cable to the spool housing.

How do you replace a lever assembly?

Quote from the video:
The lever is located just beneath the spool. Inside the trimmer head to remove it on cert a screwdriver. Through one of the tab openings on the trimmer head and that I can get it underneath the lever.

How do I fix my Black and Decker grass trimmer?

Quote from the video:
It's secured with two tabs on either side of the trimmer. Head I just push them in and the cap will come off the spool is beneath the cap. I just pull it away from the trimmer. Head.

See also  How do you make stuff out of washcloths?

How do you fix a string on a trimmer?

Quote from the video:
Thread each end of the line through the eyelets on the trimmer head as you connect the spool and bump knob wind the bump knob based on the arrows shown on the reel. Apply pressure to wind it evenly.

Why is my Black and Decker trimmer using too much line?

Your Black and Decker trimmer feeds too much line because there’s a malfunction with the auto-feed lever. The auto-feed lever regulates the amount of line that feeds out. As a result, the auto-feed lever gets a lot of use and can wear out over time, leaving too much line coming out.

Why does my trimmer line run out so fast?

Here’s why, over feeding the string will waste a lot of string, if you keep tapping, it keeps coming out, and getting cut by the blade on your trimmer head. You could literally run out of string by just feeding more string too often. Practice feeding, only when you need it.